Speed sensor signal isolation, acquisition and transformation, sine wave and sawtooth wave signal input, square wave signal output, signal converter

DIN11 Series speed sensor signal isolation transmitter

The main features :

The speed sensor signal is directly input , Shaping and conditioning square wave signal
200mV Amplification and shaping of weak peak signal
Sine wave 、 Sawtooth signal input , Square wave signal output
Do not change the frequency of the original waveform , Fast response
Power Supply 、 The signal ： Input / Output 3000VDC Three isolation
Power supply ：5V、12V、15V or 24V DC single power supply
Low cost 、 Small size , Easy to use , High reliability
standard DIN35 Rail mounted
Size ：106.7x79.0x25.0mm
Industrial grade temperature range : - 45 ~ + 85 ℃
application ：

Speed sensor signal isolation 、 Acquisition and transformation
Vehicle speed measurement
automobile ABS Anti-lock braking system
Speed signal amplification and shaping
Ground wire interference suppression
Motor speed monitoring system
Speed measurement and alarm
Signal distortion free transmission and transmission
Product selection table ：
DIN11 IBF – S□ - P□ – O□
Input signal Power supply The output signal
characteristic Code Power Code characteristic Code
Positive and negative signal input , Sine wave input
Amplitude peak to peak （VP-P）：200mV~50V S1 24VDC P1 Output level 0-5V O1
Single ended signal input ,
Amplitude peak to peak （VP-P）：5V S2 12VDC P2 Output level 0-12V O2
Single ended signal input ,
Amplitude peak to peak （VP-P）：12V S3 5VDC P3 Output level 0-24V O3
Single ended signal input ,
Amplitude peak to peak （VP-P）：24V S4 15VDC P4 Open collector output O4
User customization Su User customization Ou
http://www.szbeifu.com/
Examples of product selection ：
example 1： Input ： Speed sensor , Sine wave VP-P：200mV~10V; Power Supply ：24V ; Output ：0-5V level model ：DIN11 IBF S1-P1-O1
example 2： Input ： Speed sensor , Sine wave VP-P：200mV~10V; Power Supply ：12V ; Output ：0-24V level model ：DIN11 IBF S1-P2-O3
example 3： Input ：0-5V level ; Power Supply ：24V ; Output ：0-24V level model ：DIN11 IBF S2-P1-O3
example 4： Input ：0-5V level ; Power Supply ：12V ; Output ： Open collector output model ：DIN11 IBFS2-P2-O4
example 5： Input ： User customization ; Power Supply ：24V ; Output ： User customization model ：DIN11 IBF Su-P1-Ou
General parameters
Parameter name Testing conditions Minimum Typical values Maximum Company
Isolation voltage 1min 1500 3000 VDC
Signal input amplitude （VP-P） 0.2 10 60 V
frequency 0 10 500 kHz
Input impedance 10 kΩ
Input current 5V Input 0.45 mA
Signal output amplitude （VP-P） O1: Output level 0-5V 5 V
frequency 0 10 500 kHz
voltage （ High level ） O1: Output level 0-5V 5 V
voltage （ Low level ） 0 0.05 V
electric current （ High level ） 2 5 mA
electric current （ Low level ） 2 8 mA
voltage O4: Open collector output 5 30 V
electric current 3 10 mA
response time 1500 ns
Auxiliary power supply voltage User customization 3.3 12 24 VDC
electric current VD=12V 83 mA
Auxiliary power consumption 1 W
Working environment temperature -45 85 ℃
Storage temperature -45 85 ℃

Pin name call Sketch Statement Pin name call Sketch Statement
1 PW+ The positive end of the power supply 7 IN+ Analog signal input positive terminal
2 NC Empty feet 8 IN- Analog signal input negative terminal
3 GND The negative end of the power supply 9 NC Empty feet
4 OUT+ Analog signal output positive terminal 10 NC Empty feet
5 OUT- Analog signal output negative terminal 11 NC Empty feet
6 NC Empty feet 12 NC Empty feet
It can be installed in standard DIN35 On the guide rail

matters needing attention :
1、 According to the packing list before use , And product labels , Carefully check and confirm the product quantity 、 Model and specification .
2、 When using, it must refer to the wiring diagram corresponding to the selected product model , Connect the signal input correctly 、 Output and power cord , Turn on the power supply and signal after checking that there is no error .
3、 When measuring the signal directly with the probe , Please tighten the terminal .
4、 The operating environment shall be free of conductive dust and damage to insulation 、 Corrosive gases of metals exist .
5、 During centralized installation , Installation spacing ≥10mm.
6、 The product has been adjusted when leaving the factory , Do not adjust at will . When on-site adjustment is really necessary , Please contact our company .
7、 The product is an integrated structure , Non detachable , At the same time, collision and falling shall be avoided . This product is guaranteed 2 year , in the meantime , The company will repair or replace... Free of charge . If any label on the product is artificially damaged or altered or torn off, it will not be returned or replaced .
8、 There is no lightning protection circuit inside the product , When the input of the product 、 When the outgoing feeder is exposed to outdoor harsh weather environment , Please take lightning protection measures .
9、 Product specifications are subject to update without notice .
guarantee ：
Within two years from the date of sale , All users shall abide by the storage rules 、 Transportation and use requirements , And the product quality is lower than the technical index , You can return to the factory for free maintenance . Damage caused by violation of operating regulations and requirements , The device fee and maintenance fee shall be paid .
Copyright ：
Copyright 2012 Shenzhen Beifu Electronics Co., Ltd .
Without permission , Do not copy 、 distribution 、 Translate or transmit any part of this manual . If there is any modification or update to this manual , Without notice .
trademark ：
Other trademarks and copyrights mentioned in this manual belong to their respective owners .
Version number ：V1.2
date ：2012 year 9 month